Synchrodyne Electro-acupuncture Training Manual Chapter Twelve "Remedy by Area Testing."

Home|Health Articles|Hall Of Fame|Useful Links

 

Click Here to vote for the topics you want the know more about.

Click Here to sign up for the monthly HealthyDoctors Insight Newsletter.

 

Would you like to exchange links with our website?
 Click here and send us your website information.

 Alternative Health and Complimentary Medicine Directory

  

REMEDY BY AREA TESTING

  1. If you want to use the patient’s urine as a biological filter, take the coil cord that is attached to the gauze covered cylinder the patient is holding and remove it from the gray-white remote input and plug it into any small hole in the round circular base of the Duplicating Well. Make sure one red wire from the Duplicating Interface Box is also plugged into the base.

  2. Plug the other red wire from the Duplicating Interface Box into the same gray-white remote input hole where you just removed the gauze-wrapped cylinder.

  3. Place the patient’s urine specimen into the Duplicating Well and cover.

  4. Move the arrow to Remedy By Area Testing and press the key once and release. You can customize each meridian area for the substances you want to test. This is done through the Remedy Editor section of the Main Menu.

  5. Move the arrow to the meridian you want to test and press the key once and release. A new menu will appear.

  6. The following choices are new to this menu, that did not appear in Control Point Testing:

Area: Left Hand Area, Right Hand Area, Left Foot Area, Right Foot Area and Outside

Area.

Point: Depending on that meridian you are on, a list of the points of the meridian will

appear.

Potency: Allows you the opportunity to change potency of the homeopathic on the

testing platform, by changing the settings on the Tune Relative Intensity Meters. 5X

DIAL 521-821, 6X DIAL 311-632, 8X DIAL 581-455, 10X DIAL 743-291,12X

DIAL 388-711, 15X DIAL 501-861, 30X DIAL 951-822, 60X DIAL 591-475,

100X DIAL 773-201, 200X DIAL 338-791 and Sample DIAL 000-000.

IMPORTANT: MAKE SURE THE POLARITY METER IS SET AT 000.           

 

  1. Move the arrow to Audio and select the desired Pitch.

  2. Move the arrow to Potency, hold down the key. Drag the arrow to the potency you desire, enter the two sets of three numbers into the Tune Relative Intensity Meters, and then release the key to lock in this potency.

  3. Set the Polarity Meter to 000. You can change the potencies only for homeopathics that are on the Testing Platform. The entire Testing Platform is active. You cannot select Cylinder Set 1, 2 or 3 individually.

  4. Move the arrow to Area, hold down the key, move the arrow to the desired area you want to test, and release.

  5. Move the arrow to Point, hold down the key, and move the arrow to the desired area, and release.

  6. Before testing any remedies, it is important to retest the point you will be testing to determine what the maximum and minimum readings are at this time.

  7. The testing should be done in the clear, with nothing on the testing platform. Use the arrow to choose the rectangular box with the listing CLEAR MEASUREMENT test the point to record the results for future reference.

  8. Now you are ready to test the remedy or remedies against the point you have just tested to establish it's current maximum and minimum readings. Load the samples or sample you want to test into the multi-hole, shallow, or deep well inserts and place ONE on the Testing Platform in Set 1.

  9. Move the arrow to a selection that identifies the sample or samples you want to test. If the bottles are not color-coded and mixed together in a random order, record the

  10. results in the rectangles labeled Group #1, Group #2, or Group #3.

  11. If your samples are color-coded, use the listings for the color-coded trays. When you have the arrow on the correct rectangular box and press the key, the rectangular box will become highlighted, indicating that a test can be made.

  12. Have the patient hold the gauze-wrapped cylinder in the opposite hand of the side being tested, locate the point with the probe, and test.

  13. If the result of the test is not closer to 50 with less of an Indicator Drop than the initial test, change the potencies by selecting a new potency listing from the Potency Menu.

  14. Change the settings on the Tune Relative Intensity Meters to change the settings inside the Synchrodyne. Be sure the Polarity Meter is on 000.

  15. Test again and if this does not produce a more balanced reading, choose other potencies. Usually, you will try 6X, 12X, 30X, 60X, and 100X.

  16. If the different potencies do not give you a better balance, then try different trays of

  17. samples or individual substances to find something that will provide a better balance.

  18. You can test only one well insert containing up to 22 remedies at a time on the Testing Platform. If you want to use a process of elimination to find the one substance that balances, find a tray that creates a better reading.

  19. Break the group of vials up into three groups.

  20. Place each group in a different multi-holed well insert.

  21. Use the arrow to select Set 1 to record the readings.

  22. Place a multi-hole insert on the Testing Platform in any Cylinder Set.

  23. Test the point and evaluate the result.

  24. If the point is balanced by this group of substances, break them up into three groups and test each group alone on the Testing Platform, using the choices of Set 1, Set 2, and Set 3 boxes to record your results.

  25. If the first group did not balance the point, remove the first group of remedies from the Testing Platform.

  26. Place the second group of remedies on the Testing Platform and use the Set 2 box to record the results.

  27. Use Set 3 box to record the results if you have to test the third group of remedies. Remember the entire Testing Platform is active!

  28. Once you narrow down the remedies to three or four, then use the arrow and the Down feature to locate the name of each remedy and test them individually. Be sure to have only the remedy you are testing on the Testing Platform at any one time. When you have found the best remedy, then try different potencies to find the one that is the most balancing.

  29. Once you have discovered the best remedy and potency, move the arrow to Print and hold down the mouse key until Type Report and release. The printer will print out the test results and you will return to the menu that lists the meridians.

  30. You can choose another meridian to test or go to Exit to return to the Main Menu.

 

Home|Health Articles|Hall Of Fame|Useful Links

Click Here to vote for the topics you want the know more about.

Click Here to sign up for the monthly HealthyDoctors Insight Newsletter.

 

Disclaimer |Terms Of Use |Privacy Policy

©Copyright 2003 HealthyDoctors.com * All Rights Reserved  
Office 619-990-9492  *  E-mal: info@healthydoctors.com